As a homebuyer, it’s pays to know how important water is in carrying out everyday activities, such as cooking, washing, bathing, and drinking, among many others. Because of this, you should be responsible in keeping your supply safe and clean to protect your family and pets from any potential health hazards. This is where installing a water system in your home comes to the rescue.
To get started with this project, keep reading this article to learn how you can set up your home’s water system.
Install A Water Storage Tank
If you’re looking to have a good water system in your home, the first thing you should do is to set up a water storage tank. It refers to a container that can be used for storing water. Also, its primary purpose is to provide water wherever it’s needed, such as for drinking, home cleaning, building maintenance, and many more. For instance, even if your property is supplied by a well or the local water system, installing tanks as part of your water system allows you to harvest rainwater and, in turn, help you save money on your water bills.
Hence, if you’ve decided to install a water tank, below are a few tips to consider:
- Prepare The Base Of The Tank – Regardless of the type of tank you’re installing, you’ll need a flat and level base for it to stand on. This means creating an even surface that’s bigger than the tank itself. However, it’s important to ensure that the base isn’t jagged to avoid destabilizing the tank.
- Create Overflow Draining For Rain Harvesting – Again, a water storage tank can be used to harvest rainwater. Thus, if you want your tank to do rain harvesting, you should install an overflow drainage. To do the process by yourself, be sure to drill a hole, and install a gasket and a filter, if necessary. Once you’re done, drill some screws to ensure the fixture is placed securely. By doing this, you can make sure that any excess water can escape and doesn’t erode the tank base due to water overflow.
- Set Up Your Fill Pipes From Your Roof – Now that you have an overflow drainage for rain harvesting, the next step is to fit your pipes from the roof to your tank lid. For instance, if you’re setting up a water tank for human consumption, it’s important to contact your tank supplier or dealer about the right type of filter you’ll need. Fortunately, the tanks at this site come in different types and sizes that can work best for your water requirements.
As you can see, installing a storage tank for your home’s water system appears to be a daunting task, but there are ways to help you simplify the process. However, if you think the installation process can be best handled by professionals, you can contact a reliable installation service provider to assist you.
Set Up A Water Filter
Aside from the water tank, setting up a water filter is also crucial to your home’s overall water system. It’s a device intended to remove impurities by reducing the contamination of water through a fine physical barrier and a chemical process. Consequently, you’ll prevent your water supply from being contaminated.
Thus, if you want your water system to be fully functional and, at the same time, safe and clean, below are a few steps to follow:
- Drain The System – Before installing a water filter, you should first drain the system. You can do this by turning off the main water supply. Then, open a faucet to let go of the pressure and to drain most of the water in the system.
- Make Cuts Into The Pipe – After choosing the location of your filter, it’s time to cut the pipe using a pipe cutter. You can do this by tightening the cutter into the pipe to ensure the blade lines up with your mark. Continue rotating the cutter around the pipe until you cut out a particular section.
- Attach And Tighten The Fittings – To fully install the water filter, be sure to attach the fittings properly by placing a compression nut, threading a bass fitting into the ports of the filter housing. Then, don’t forget to use teflon to ensure a tight seal between the fitting and the filter port.
- Install The Filter – Once you have all the fittings attached, the last step is to position the filter on the water line to ensure the water flow comes through the ‘in’ portion and exits through the ‘out’ portion. Lastly, use two wrenches to tighten the fittings to keep the water filter upright and straight.
Conclusion
Indeed, having a functional water system in your home is undeniably important. With this system in place, you can ensure a good and stable supply of water for your family’s health. Luckily, by following the tips mentioned above, you can quickly set up your home’s water system without hassle. However, if you believe the installation should be taken care of by someone else, you should hire an experienced company to handle the job.
